It’s As Simple As 1, 2, 3, To Test A Chainsaw Ignition Coil With A Multimeter
There is a good chance that the ignition coil has fried and your chainsaw won’t start. In this article, well show you how to test a chainsaw ignition coil with a multimeter. This is an inexpensive and easy way to determine if your chainsaw needs to be serviced.
Testing a chainsaw ignition coil with a multimeter is a simple process that can be done in just a few minutes. These are the steps to check your ignition switch.
What You’ll Need
There are some things that you will need to test the chainsaw ignition coils with a multimeter. The multimeter and the ignition coil will be required. You can start the testing process once you have these two items.
First, identify the terminals of the ignition coil that are used for primary and secondary windings.
Once youve identified those terminals, set your multimeter to resistance mode and measure the resistance between the two terminals. If there is no continuity between these terminals, the ignition coil needs to be replaced.
Each wire has two connections. Determine the resistance to Ohms mode of each wire and then measure its resistance between them.
How To Test A Chainsaw Ignition Comil Safely And Easily With A Multimeter
Step 1: Remove The Ignition Coil Cover
The first step is removing the ignition coil cover. Once its gone, you can verify the continuity status of the ignition coil. If its continuous, the ignition coil is working, so you can proceed to the next action.
Step 2: Disconnect The Ignition Coil Wire From The Spark Plug
The connecting wire on a chainsaws spark plug connects to the ignition coil. It is essential to check for continuity before beginning the chainsaws ignition coil. You can do this by disconnecting the spark plug wire and using a multimeter to check for continuity.
Next, set the device to continuity. Stick one prong on each end of the ignition coil wire. If one prong detects continuity, the wire can be reconnected.
You might read the article on the best oil for chainsaws.
Step 3: Unscrew The Ignition Coil Retaining Screws
You will need a Phillips-head screwdriver to remove the ignition coil retaining screws. Turn counterclockwise and place the screwdriver into the recess on top of each screw.
You may need to apply force to loosen them. You can manually remove them once they have become loose.
Step 4 – Remove The Ignition Coil
The coil is part of the ignition system that pushes up a little chainsaw. When its bad, the engine will not start. To check if the coil is bad, you can use a multimeter.
Step 5: Connect The Red Probe Of The Multimeter To The Positive (+) Terminal Of The Ignition Coil
The part of the chainsaw engine that is responsible for the activation of the machine is known as the ignition coil. The ignition coil converts low voltage from the battery to the high voltage required to start the chainsaw.
A multimeter can be used to test the ignition coil to see if it functions properly. The red probe should connect to the (+) terminal.
Step 6 – Connect The Black Probe From The Multimeter To A Negative (-) Terminal On The Ignition Coil
Its a simple process to test the ignition coil of a chainsaw using a multimeter due to the quick nature of the connection. Connect the multimeter’s dash probe and the negative (+) terminal to test the ignition coil. Once you have connected the probe, turn on the meter and wait for an indication to appear. If the reading is not there, you’ll need to restart.
Step 7 – Turn On Your Multimeter And Set The Resistance Or Ohms To It
You will need to set your multimeter to both Ohms or Resistance in order to test the chainsaw’s ignition coil. First, remove the spark plug wire from the spark plug and the ground wire. Next, connect the red wire of the multimeter with the ground wire. The black lead should be connected to the ground. Finally, turn on the multimeter and set it to Ohms or Resistance.
Step 8: Hold Down The Trigger Of The Chainsaw And Check For Resistance
Anyone whos ever used a chainsaw knows that it is a dangerous tool. With the potential to cause serious injury, it is important to take the necessary precautions when using this piece of equipment. It is important to inspect the ignition coil. In order to do this, a multimeter can be used.
How Do I Know If My Chainsaw Coil Is Bad?
It can be time-saving and cost-saving to determine if your chainsaw’s ignition coil is defective. This is how you can test it using a multimeter.
1. Take the spark plug wire out of the spark plug.
2. Disconnect the negative cable.
3. Connect the red lead from the multimeter to one of the spark plug terminals, and connect the black lead to the ground.
4. Let the engine idle for approximately 400 degrees F.
5. The multimeter can be used to measure the voltage at each spark plug terminal, and then display the results in a table.
6. If any of the readings are high (>14 volts), replace your chainsaw ignition coil immediately!
How Many Ohms Should A Chainsaw Coil Have?
When it comes to chainsaw coils, there is no one set answer. Experts agree that a chainsaw should have at most 0.42 ohms resistance.
This theory is based upon the idea that sparks will not fly out of the chain into your hands or eyes if there is enough resistance.
It is always a good idea to consult your chainsaw’s owner manual for details on the resistance required by your particular model.
How Do You Know If A Coil Has 6 Volts Or 12 Volts.
It is hard to identify the voltage of a coil if it is not marked as either 6 or 12 volt. To check the resistance of the coil, you can use an ohmmeter. If the coil has a resistance of less than 1/8 of a ohm, then it is most likely 6 volt. If the coil has a resistance of more than 1/8 of a ohm, then it is most likely 12 volt.
How Do You Check A Coil On A Husqvarna Chainsaw?
When you are checking the chain on your Husqvarna chainsaw, it is important to make sure that the chain is properly lubricated and that the coil is in good condition. To do this, follow these simple steps:
1. Take out the spark plug.
2. Check the tip of your chain for wear. If there is excessive wear or damage, replace the chain with a new one.
3. Lubricate all moving parts of the engine with a quality oil and replace any worn or damaged parts using new gaskets and screws as needed.
4. You can check that all screws are tightened by turning them with a wrench. If they aren’t tight enough, use a screwdriver to tighten them until they are.
5. Check the connections to the panel if the unit isn’t working.
Conclusion
Testing a chainsaw ignition coil with a multimeter is a simple process that can help you determine if it needs to be replaced.
