People often wonder Which Way Does A Chainsaw Blade Go On.
The way that a chainsaw blade is spinning can be determined by examining the teeth on the blade. On one side of the chain, there will be small teeth, and on the other side of the chain, there will be larger teeth.
A chainsaw that cuts with its left hand would have an even number of teeth on each side. A chainsaw with 20 teeth per inch (TPI) is an example.
To make a right-handed cut, a chainsaw must have an odd number teeth per inch. This will allow you to cut cleanly through wood and not catch on any objects.
These left-handed chainsaws can be identified by an odd number of teeth per inch, such as 13 TPI or 15 TPI.
This means that a right-hand tooth pattern saw blade must be used to cut the wood. The spinning chain must rotate the blade so that the wood is fed into it. To cut properly, a right-handed tooth pattern must be rotated in a clockwise orientation.
Therefore, when holding the running chainsaw in your hands, you should feed the lumber through the blade while it turns in a counterclockwise direction.
A chainsaw equipped with left handed (multitooth) teeth is used to cut wood. They do not provide a smooth finish and are not suitable for use in a cutting-chain.
A blade is designed to cut when it spins in one direction. Feeding the wood into the blade with the right-hand rotational pattern is correct for this saw type. The opposite direction of the wood will put more strain on the saw, and could cause damage to your chainsaw.
You also run a higher chance of kickback which can result in serious injury to yourself, your friends/ family, and bystanders if proper precautions are not taken.
Remember that a left-handed, or multi-tooth, would be used to cut down trees by pushing them into a spinning chain. A right handed, or single-tooth, would be used to make a faster cut by pulling the wood into a spinning chain.
How To Make A Chainsaw Blade Run In The Right Direction?
Chainsaws are powerful tools that could cause significant damage if mishandled. When assembling or disassembling, make sure to follow these steps not to allow an accident to occur:
Step 1 Removing The Chainsaw Casing
To remove the chainsaw casing, hold the handle steady and pull the handle off slowly. Be careful not to speed up, or you might lose control of it, leading to step 2. You can’t rush to get it done.
Have a friend help you if possible to have two pairs of hands. To prevent accidents while you move on to step 2, keep them apart once they are separated.
Step 2: Removing The Chain
Protective gear, such as gloves or safety goggles, is necessary to remove the chain correctly and safely. These can be purchased at a hardware store for around 10€.
After putting on your protective gear, you can move your hands around and around the guide to keep it from slipping.
Step 3: Identify The Direction Of The Cut
Heres a simple trick that few people know about: when chainsaws are manufactured, they will initially be sharp. When looking at the engine from 12 o’clock, you will see that it is rotating clockwise.
Therefore, you should use a drop file to sharpen your blade counter-clockwise when cutting. Do this with enough pressure and force to achieve an efficient cut. Knowing how to properly use the chainsaw is key.
Step 4 Reassembling And Tightening
You can then put the chain back together by following these steps: You will do this by placing the chain on the bottom guide bar and then snapping it onto place where tension can be adjusted by using the tensioning screws located at the back of the chainsaw’s casing.
Some models will have a hole where you can insert your screwdriver. When tightening, ensure that the screwdriver is tight enough to prevent movement but not so tight that it can damage any items.
Note: If you make any mistakes in this process, all that has to be done is disassemble everything and reassemble from the start. If you are having trouble with the process, or just can’t figure it out no matter how many attempts you make, you can consult a professional at your local hardware shop for help.
You should also be aware that if parts don’t exist or look the right way to cover a specific area, it is best not force anything in. There are high chances of something breaking eventually.
Problems Of Putting The Chainsaw In The Wrong Direction
You can cause many problems if you use your chainsaw in an incorrect direction. If you own a chainsaw and havent had any of these problems, then youre fortunate, but if you have, here is what some of these problems may be:
1. Waste Of Good Bar Oil
This happens when the saw blade is turned backwards and the saw chain starts to cut.
Bar oil will be destroyed quickly by high heat.
2. Cause Damage To Chain Link
When the saw chain is cut in an incorrect direction, the chain will run backward. The guide bar and sprocket also become hotter and more frictional, which can cause further problems for your chain.
An excellent example of this problem would be that the drive links on the side get worn out quickly because they are constantly rubbed against each other.
3. Causes Unnecessary Strain On The Guide Bar
When cutting wood with a chainsaw, it wants to pull itself into the material you are cutting at all times. This is why its essential for saw operators to always stand with their feet spread apart for a better balance of body weight while operating a chainsaw.
You can put too much stress on your guide bar if you reverse your chainsaw while you are cutting wood. This could cause it to crack.
4. It May Make You Doubt Your Skills
You might start with the forward position of the chainsaw to ensure that it cuts correctly.
Once the forward motion is perfect, you will know the cause of any problems and be able to quickly fix it.
5. Motor Deterioration
When putting a chainsaw in reverse while operating can cause extra strain on the motor and, in some cases, may lead to breakdown or even permanent damage to the electric starter.
6. Burnout Clutch
Reversely operating a chainsaw can put extra strain on the chain brake. In some cases, this can result in your chain brake being either broken or burned out.
Conclusion
So how do you turn a blade of a chainsaw ? It depends on whether you are right-handed or prefer to use your left hand for specific tasks.
Manufacturers recommend that right-handers align the top tooth on the cutting chain with the direction of rotation to tighten the blade.
In other words: If you look at the place where each tooth has been sharpened, position them inwards towards center of rotation when using right-handed chainsaws.
