It can be frustrating to try to start your chainsaw but it won’t turn on. The situation is even more frustrating when you see the engine is flooded with fuel; this leaves little room for anything else.
You feel like giving up and then realize that there is still hope in starting the machine. This article will show you how to start a flooded chainsaw.
Before we get into how you can start a flooded saw, let’s first discuss the root cause of this problem.
A lot of people make the mistake of either over-priming or over-squeezing their fuel bulb while refueling their chainsaws which leads to flooding of the carburetor.
Whatever the cause may be, there are two steps on how to start a flooded chainsaw: remove excess fuel from the combustion chamber and then try again.
Chainsaws won’t turn on if there is too much fuel. Once the fuel gets inside the engine, it can cause damage to many parts, including the valves located near the spark plugs. If this happens, your best option will be to visit a professional mechanic who will remove the excess fuel so your chainsaw is ready to be used again.
Here Are The Steps To Get A Flooded Chainsaw Started By You If You’re Up For It:
Step 1: Place your chainsaw on a flat surface before doing anything. Because your machine doesn’t need support, it will be easier to work on it.
Step 2 To expose the engine, remove all plastic and wood covers. Note that there are different models available in the market; therefore, remove only what is needed to access your carburetor.
Most will have one to two screws that hold them in place. Others may need you to remove nuts and bolts as well as cut wires. After you are done, carefully remove the wood or plastic covers to ensure they don’t get damaged.
Step 3 – Next, disconnect the spark plug’s high voltage power cap. It is typically made from rubber and contains a fuel filter. It can be found somewhere near the tip of your machines spark plug (most likely it is wet with fuel).
You can easily take it off by hand; however, make sure you are only touching the insulation part and not where it gets attached at. Once removed, place it aside for now as we will be using this later on in our process (you may choose to throw it away if you like because it does not offer anything but a mess).
Step 4 Now it’s time to take out the spark plug. This can be done with the wrench included in your chainsaw’s purchase. If you do not have one, then you can use any other wrench that fits the size of your machines spark plug.
Important: Before unscrewing your spark plug, make sure to clean off all fuel and metal parts . This will help you to create a strong connection when you start your chainsaw.
Step 5 – Now that you have removed the spark plug, look closely at the electrode to see if it is soaked in fuel. This indicates that the ignition has occurred.
If this is the case, there are two things you can do: try to start it or wait until the fuel evaporates. If you don’t have the experience to start a chainsaw after it has been flooded, waiting might be a better choice.
Step 6: Now that the spark plug is removed, use a paper napkin to plug up the hole on the cylinder where it screws in (make sure it covers the entire hole). This will prevent fuel from getting into the combustion chamber.
Step 7 – Place the chainsaw on a flat surface. Now you can start it. Make sure your hands are dry before doing anything and that there is no debris or objects near the saws muffler area.
Step 8: To start the chainsaw, first make sure it is in its lowest setting possible (this will help prevent any damage that might occur when you pull on the starter cord). To get the saw to start, you will need to hold the throttle trigger down. Continue holding the trigger until you’re ready to move on to the next step.
Our article about Best Chainsaw For Wood Carving might be of interest to you.
Now take your high voltage cap and put it back in the place where you removed it from. This part is very important, do not lose this. If it is not installed correctly or maintained after every use, your saw could catch fire or explode. Finally, pull the starter cord to spark up your chainsaw and give it a go.
What Basic Troubleshooting Techniques Are There For Default Chainsaws.
First, check your air filter to ensure it is clean. Next, check the chain lubrication for any loose screws. Spray a little bit of starter fluid into the carburetor and pull the starter cord if the saw does not start. If that still doesnt work, then the engine may need to be rebuilt or replaced. If all else fails take your chainsaw to a professional for repair.
What Are Some Common Causes Of Chainsaw Flooding?
If there is too much fuel in a chainsaw’s combustion chamber, if the sparkplug is not installed properly or if the carburetor is failing, the saw can flood. A loose or dirty chain can also be a cause.
How Can I Start A Flood Chainsaw?
There are a few things you can do to try and start a flooded chainsaw. First, clean the air filter. If its not, clean it off and try starting the chainsaw again. You can also try pouring some gasoline into the air intake to help get the engine going. If that fails, you might need to bring the chainsaw to a shop for repair.
How Do I Stop My Chainsaw Flooding?
There are several things you can do to help prevent your chainsaw from flooding, including making sure the air filter is clean, tightening any loose screws, and checking the chain lubrication. You can also try spraying a small amount of starting fluid directly into the carburetor while pulling the starter cord. If this fails, the engine might need to be rebuilt. Finally, if all else fails, take the chainsaw to a professional technician for repair.
What Are The Common Signs Of A Chainsaw Having Been Flooded?
Some common symptoms of a chainsaw that has been flooded include an inability to start, excessive smoke, and/or sparks coming from the muffler area. You may also smell gasoline or oil while trying to start the saw. You might also hear clicking when you pull the starter cord.
What Are Some Common Causes Of An Engine That Has Been Flooded?
If the spark plug isn’t installed correctly or the carburetor isn’t working properly, the engine of a chainsaw can become flooded. Other causes can include a dirty air filter or a loose chain.
What Tools Do I Need To Start My Chainsaw?
Your spark plug, also known as the high voltage cap, is all you need to start your chainsaw. Regardless of what type of chainsaw you have, this part needs to be put back into place after you have finished starting up your chainsaw.
Can I Use A Chainsaw If Its Flooded?
Its not advisable to use a chainsaw if its flooded. It can cause engine damage and make it difficult to start the chainsaw. If you try to use a chainsaw thats flooded, you may end up doing more damage to the saw. Its best to take it to a repair shop and have them take a look at it.
What Should I Do If My Chainsaw Wont Start?
If your chainsaw wont start, there are a few things you can try. First, check the air filter and make sure its clean. Clean it and then try to start the chainsaw. You can also try pouring some gasoline into the air intake to help get the engine going. If all else fails, you may need to take the chainsaw to a repair shop.
How Frequently Should I Sharpen My Chainsaw’s Blade?
Its a good idea to sharpen your chainsaw blade regularly. The frequency will vary depending on how often you use the chainsaw, but its generally a good idea to sharpen it every few months. Either do it yourself, or hire a professional to do it.
Can I Use My Chainsaw If The Chain Is Loose?
If the chain is too loose, it’s not recommended to use your chainsaw. If the chain is too loose, it can come off the bar and cause serious injury. You should take your chainsaw to a shop for repair. They will inspect it. You might be able to have the chain tightened by them.
Conclusion
You now know how to use a flooded chainsaw to cut wood. You should follow the safety precautions and instructions that were given earlier and you will be fine.
